Thefire triangle below shows that three components are required to supportconbustion. The presences of fuel, oxygen, and heat are all essential: removeany one of the three and the fire self extinguishes.
Of the normally encountered textile fibres, wool is the mostflame resistant. Wool has the most complex fibre structure optimised throughevolution to provide thermal protection to mammals. Several factors in thisstructure are also responsible for wool's natural flame resistance.Specifically, compared with other common fibres, wool:
While most textile fibres are polymers containing mainlycarbon and hydrogen that can burn easily, wool also contains high levels ofnitrogen and sulphur. In fact many fire retardant additives used for othermaterials are high in nitrogen. Wool therefore requires higher levels of oxygenin the surrounding atmosphere to accelerate combustion. The limitingconcentration of oxygen required to support combustion of wool in standardtests is higher than the ambient oxygen concentration in air (21%). Thereforeit is difficult to ignite wool, but once ignited, the flame speads slowly andit is easy to extinguish.
Wool fibres are assembled from keratinised cells. Theelongated cortical cells in the centre of the fibre are protected from theenvironment by a layer of cuticle cells. These outer layer cells contain highlevels of sulphur. On addition, the fibre is held together by a lightlycrosslinked cell membrane complex. When wool is heated to the point ofcombustion this structure tends to foam providing an insulating layer ofpyrolysed material separating heat and oxygen from the fuel.
Due to its natural low flammability characteristics, woolhas traditionally been the fibre of choice in many technical applications,ranging from nightwear and protective garments, to transportationandspecialized military requirements.
Fabric structure and density (mass per unit area) togetherwith considered product design are important parameters when considering theflammability performance of textile products. Heavier and denser fabrics with aflat surface together with air excluding designs are known to give the bestperformance.
The wider fire science community now recognizes that rate ofheat release determines the real hazard in actual fire situations and varioustests have been developed to measure this property. For example, fibres such ascotton which have a low heat of combustion have a relatively high rate of heatrelease that determines fire spread rate and burn severity. Wool has both a lowheat of combustion and a low rate of heat release.
The table below provides a relative summary of the flammability properties of selected fibres, although the actual values vary depending on the test methods employed.
The evolution of increasingly severe mandatory flammability regulations in many aspects of domestic, social and business life has meant that even inherently low flammability fibres, such as wool, require a flame retardant treatment for some applications. Typical applications subject to mandatory flammability requirements include children's nightwear, domestic and commercial furnishings, public transportation and protective clothing.
The flame resistance of all textiles, including wool products, can be improved by selected chemical treatments. Initially, fire retardant treatments for wool were based on the impregnation of borates, phosphates and to a limited degree the organic phosphorus compounds more commonly associated with cellulosic fibres.
The introduction of stricter flammability requirements for airline furnishings resulted from a review of general aviation standards coinciding with the release of wide bodied aircraft in the early 1970's. Many flammability treatments available at the time did not satisfy the new requirements, so The International Wool Secretariat developed a new flame retardant treatment based on the reaction of zirconium or titanium salts with wool. A suite of treatments, based on these two actives, was eventually developed under the generic title of Zirpro, to cover a variety of flammability standards and care claims. The Zirpro treatments can combine flame resistance with shrink resistance, oil and water repellency and in some instances, dyeing.
Zirpro treatments are based on the exhaustion of negatively charged zirconium or titanium salts, under acid conditions, onto positively charged wool. This results in the deposition of only about 3% of flame retardant inside the fibre with negligible effect on properties such as handle. These treatments stabilize and further crosslink the protein structure. The best treatments are colourless; do not alter wool's natural properties, such as handle and moisture adsorption, and tend to be deposited near the surface of the fibre. These treatments tend to increase and strengthen the insulating foam produced as wool is decomposed by heat. Zirpro treated wool also has good durability to washing and drycleaning.
Since the introduction of Zirpro, several different classes of flame retardants have been developed for wool, one of which is based on the application of highly effective halogen donors. The halogens in the treatments tend to interfere with free radical processes that maintain the flame. The use of halogen donors is now restricted by changes to environmental legislation stressing the need to develop alternatives. In spite of the environmental shortcomings, halogens and their derivatives still form a diverse and important role in the flame resist treatment of many products, not just textiles. Alternative treatments are based on phosphorous compounds which tend to lower the thermal decomposition temperature of the textile allowing the volatile fuel to escape before the ignition temperature is reached.
Recent research into flame retardants has focused on the development of intumescent agents. These agents combine the attributes of flame retardancy with the formation of a high thermal resistance insulating char layer. Although originally developed for cellulosics, wool specific intumescents have now been formulated to enhance the natural flame resist and char formation properties of wool.
Wool's natural flame resist properties, the availability of alternative flame resist treatments and the ability to blend wool with flame resist fibres ensures a good future for wool in highly specified, technical and novel end products.
To read more articles on Textile, Industry, Technical Textile, Dyes & Chemicals, Machinery, Fashion, Apparel, Technology, Retail, Leather, Footwear & Jewellery, Software and General please visit https://articles.fibre2fashion.com
To promote your company, product and services via promotional article, follow
this link: https://www.fibre2fashion.com/services/article-writing-service/content-promotion-services.asp
Comments